Friday, September 4, 2015

Basing, storage and transport.

Hi All

I've been doing a lot of prepping of figures over the last week, but don't fear, I still have a mountain of lead and plastic.

This stuff is mostly 20mm stuff that I purchased from Splintered Light Miniatures awhile back. I'm including a few 28mm figures that I wanted to get done as well. I still need to have a sort through and prioritize my painting.

Anyway, after seeing other peoples stuff and getting a lot of tips, I wasted time did the necessary internet research on the various topics.

Basing: I think my general fantasy basing scheme is going okay. I'm using all the old and new square plastic bases that I have. One thing I've hit upon to tackle scale creep/ integral base is to use either the thin plastic rendera bases or 1.5mm plywood from Litko. For my 1/72 (20mm) projects I'mm still using the fender washers 3/4" (~20mm) and larger for monsters etc. Where I'm not sure what to do next is my planned foray into 40K or Sci-Fi/ Post Apocalyptic / Space Trash games. My 28mm basing for non Warhammer Fantasy Battle has been a little all over the place. Thus far I've primarily used 3mm thick 1" (25mm) wood discs that you can buy at the craft store. I've also used one of the lipped bases, I think it ends up being slightly larger than 25mm at the edge but the top area seems the same as 25mm. I was looking at info on 40K and there seems to have been a switch from 25mm to 32mm for most troops, with larger bases like 40mm and 60mm for monsters/ robots. Putting a Space goblin on 25mm seems like overkill, but I can see the appeal of not having to have so many different base sizes. I have some 20mm plastic slotta bases that I'm not going to use for 20mm metal zombies. I guess the open question is, what do you do for your sci-fi? I feel like I should try a different basing scheme as well.

Storage: I feel like the Sterlite plastic containers have done their job adequately. One innovation that I saw at Oldhammer USA was the addition of sheet metal to the bottom of the bin and rare earth magnets on all the bases. I have been using the metal roof shingles from Home Depot for basing 20mm cavalry and engines, but I was having trouble finding what they call "craft steel" in 12" x 12" squares. I finally found it in aisle 20 of my local Home Depot, near the specialty fasteners. Coincidentally it is the same aisle as the rare earth magnets. Now I did purchase some magnets there, but they were 3mm thick and don't fit completely underneath a standard slotta base. Some more research showed that many use 2mm thick magnets because they a strong enough to stick to metal even with a 0.5mm gap. Of course in America we don't use metric measurments so I may try 1/8" (3mm) x 1/10" (2.5mm) disc magnet from K&J Magnetics here. Again any thoughts you may have to share are appreciated.

Transport: While I did use the Sterlite containers and seat cushion foam to transport my figures in my check on luggage, a few people were using jewelers cases to transport their figures. The recommendation I got was for Nile Corp. Jewelry Supply and I think what I saw was one of the aluminum cases from here. I'd need to review carry on sizing restrictions but I think 861-7 might be the way to go. I'm not sure if the 26" dimension on the 862-7 puts it out of carry on size. Any how you could use magnets and sheet metal in the trays and add foam to reduce impact. I'm gong to seriously investigate this.

I want to close with calling your attention to Belched from the Depths, particularly their tutorials which cover many of these topics. If you have any links or suggestions for things that work for you feel free to let me know.

8 comments:

  1. I tend to use really useful boxes and have the miniatures stand in movement trays, but I am always worried about the way that the slide around. I must investigate your magnets idea a bit more, just for peace of mind.

    ReplyDelete
    Replies
    1. Hi Michael, I have one really useful box and they are quite good. The Sterlite brand is just easier to buy and cheaper over here. The idea is to cut a metal sheet to size and epoxy glue it to the bottom of the box. Then the magnets glued in your figures bases should have something solid to hold onto. Right now I use foam to immobilize my figures, but there is a lot of waste.

      Delete
  2. Magnets are the way to go but would involve re-basing for me.

    ReplyDelete
    Replies
    1. Hi Fran, right now I don't think I would have to re-base much of anything. One quick solution I've thought of after looking at the magnet website is the metal magnet sandwich. Since my 1/72 stuff is on metal washers, I wouldn't be able to put magnets on them. But if the bottom of the box has a metal sheet and the base is metal, why couldn't I put a magnet in the box and a figure on top of the magnet? At some point I will have to investigate retro fitting solid bases with magnets. I'll let you know when I get there.

      Delete
  3. I use quite a mixture of steel washers, plastic, MDF and card bases, depending on the model. These are then stored in foam.

    It shouldn't be too hard to add a tiny magnet to an existing figure that's based with a washer, I imagine. After all, the washer already has a hole in its centre so as long as you haven't filled it then the magnet might just fit there?

    ReplyDelete
    Replies
    1. Hi Hugh, fantastic idea to put the magnet in the washer hole! It would require a very thin magnet, but I'm pretty sure they make them that thin. The internet brain trust wins again. Thanks.

      Delete
  4. As you saw at the event I've gone for the Aluminum Jewelry box and I really like it...though I need to get the smaller version as well...the big one is just too big for ease of transport. I got mine from: http://www.gemsondisplay.com/shopdisplayproducts.asp?id=88 they seem to have slightly better prices than Nile. however...I still need to invest in the rare earth magnets and the metal liners for my trays...things still shift around in my case too much for my liking.

    ReplyDelete
    Replies
    1. Hi Blue, thanks for the link. I think your rig would benefit greatly from the steel sheet and magnet combo. I've had a lot of experience around the house of my figures sliding all over the place in bins, so I know that immobilizing the figures is a priority if you're going to be moving them around.

      Delete